The changes I’ve made (as you can see in the 3rd picture):

1. Add a X Endstop support, because it didn’t always switch and the x-carriage crashed several times against the X-Idler.
2. Another problem was the belt holder. It didn’t hold the “softer” GT2 belt, neither the original Anet A8 belt. So I reduced the distance. Don’t know, if the original belt fit into the belt holder.
3. The belt holder has not the correct height for the X-Idler from Leo_N. I increased it by 2mm.

This is the belt I’m using with much better results: https://goo.gl/yXBLgi

Download

Download the 3D Model on: https://www.thingiverse.com/thing:2251627

The post Remix of Anet A8 Jan 2017 model Prusa X carriage remix appeared first on MightyNozzle.

I only tested this design for the original Rev1.3 raspbbery pi cam. If you want to use it with another cam module, check the differences of the dimensions before you print this thing.

You need following parts for vanilla raspberry camera:

• camera_holder_bracket_for_anet_a8.stl
• camera_mount_front_by_DanielBull.stl
• camera_mount_back_more_space.stl
• camera_mount_hinge_by_DanielBull.stl

You need following parts for raspberry camera with M12 hack:

• camera_holder_bracket_for_anet_a8.stl
• camera_mount_front_m12.stl
• camera_mount_back_more_space.stl
• camera_mount_hinge_by_DanielBull.stl

You can mount the holder on each of the 2 outer holes on the back of the printer:

• top left hole for the Anet A8 Board (picture). The M3 screw should be 4mm longer
• left hole of the bottom left hole of the Anet A8 board. You need a M3x16+mm screw + M3 nut and a washer (optional)
• same on the opposite side, where the power supply is mounted.

Depends on how far away your raspberry pi is from the camera, you may need a longer ribbon cable: https://goo.gl/8y9xqR
For the M12 hack, I used the lens + lens mount + lens cover from this arduino module: https://goo.gl/hfU63k

Download

Download this 3D Model on: https://www.thingiverse.com/thing:2199829

The post Anet A8 Raspberry Pi Cam Holder appeared first on MightyNozzle.

Features:

• doesn’t need much filament (about 75g PLA).
• modular – you don’t have to throw the whole case away, if you change the board. You can just use or create another board holder. Thats 10g for a holder vs 100-200g for a whole case.
• no need to drill holes in your Anet A8 acrylic frame.
• you can use the board holder without the frame!

BOM:

• 3x M3x20 mm screw (alternative M3x8 or M3x10) for RAMPS board
• 4x M3x12mm screw (alternative M3x8 or M3x10) for Raspberry Pi 2/3
• 6x M3x8mm screw (alternative M3x10 or longer) for the case lid
• 4x M3x12mm screw, if you mount the case frame with normal nut and without washer. Use M3x16mm screw for nyloc nut w/o washer
• 2x M3x16mm screw for the board holder
• 6x M3 nut (or nyloc nut)
• optional 6x M3 washer

Electronics:

• 90° angled USB A to USB B cable, if you want use the RAMPS board together with the Raspberry Pi: https://goo.gl/raHXUa
• RAMPS 1.4 Board: https://goo.gl/YBxuOz
• Mega 2560 Board (Arduino Clone): https://goo.gl/rVB4LO
• 4-5x DRV8825 Stepper Driver: https://goo.gl/TpAO0U
• Raspberry Pi 2 or 3

Download

Download this 3D Model on: https://www.thingiverse.com/thing:2195886

The post Modular Anet A8 RAMPS 1.4 + Raspberry Pi 2/3 Case appeared first on MightyNozzle.

Make sure, that the length between display backcover and frontpanel is about 23.5mm and the frontpanel height about 80mm. This should be the stock size. It is also compatible with the “Anet A8 Brackets to Reduce X-Axis Motion” by Leo_N: http://www.thingiverse.com/thing:1872162 , but it is not required.

There are two versions of the holder. The plain holder and a chamfered one. I think, the chamfered one is more stable than the plain one.

The holder is pretty stable and it only needs about 15g of filament (PLA) each. You need to the print the holder (plain or chamfered) two times.
I also recommend to print the second holder in mirror. The design is unidirectional, but the first layer that sticks on the printbed differs always of the last layer.

You should also use a spool adapter that fits on the 8mm threaded rod like this one: http://www.thingiverse.com/thing:767317

Update

Because I changed the direct drive extrude to bowden setup, I didn’t use this spool holder any more. I’ve added the 123D Design files, so you can change this holder as you like. In respect of the CC License, you can remix this spool holder as you like.

Download

Download this 3D Model on: https://www.thingiverse.com/thing:2162266

The post Anet A8 Spool holder – reuse Anet parts appeared first on MightyNozzle.